83 toyota pickup bump stops install install#
83 toyota pickup bump stops install driver#
83 toyota pickup bump stops install upgrade#

Supposed to be a cheap/easy trick and because of the additional

However, we suspect this is overkill, especially because this is Result in higher clamping force as well as resisting shear forces.

Mount the stud or bolt in a different location (often forward on the knuckle)ДЄlmost all of the above variations use tapered fasteners which will.

There are a few variations to the Toyota 5th stud mod. There are lots of variations on this method. However, if you have any variance in that combo in theДЇuture, you may need to change your shims. One set of bearings, you could set your shims once and never need to do In theory, with one set of steering arms, one set of knuckles, and Remove arm and shim fifth stud and steering arm

Shims method: Weld the tab to the arm with both pieces installed but.

83 toyota pickup bump stops install install#

No shims method #2: Install all parts with correct shims and weld everything up.

Have a little give so that you donвЂ™t have to worry about shims. Steering arm is set up, shimmed, and the four stock bolts are torqued.

No shims method #1: Weld the tab to the arm with both pieces.

Shims! In theory, it would seem that you would need to shim your new Here are the options: 1) Upgraded Studs: Bolt-In Strength If you have smaller tires, wheel easier trails, and generally put less stress on your Toy, high or medium strength threadlocker are fine. Why? Because you should re-torque your stud nuts before every tough trail ride and plain anti-seize will make it easier.

Now, we're leaning towards using anti-seize on the stud nuts. This was so that when you snapped a stocker (more likely) it would be easier to pull off the steering arm to get at the broken Birfield. The only exception is Loctite: Use high strength red Loctite on theДЇor the stud nuts, we used to recommend high strength red Loctite if you have chromo Birfields or medium strength blue Loctite if you have stock Birfields. Paint on your cone washer surfaces or in the steering arm taper is a When you install stud parts and steering arms, all mating surfaces must be clean and dry of oil, grease, and paint. Recommend regularly checking your studs until you find out how often We suspect a major difference between the different strengthening options is related to maintenance.ДЇor a given truck, you probably wonвЂ™t have to torque the nuts asДЇrequently when you have Dana 44 studs or a 6 stud knuckle. Properly torqued, are fine for the lower knuckle studs. Upgrading the upper studs where the steering arms mount. Note that we are almost always talking about There are several methods now that you can

83 toyota pickup bump stops install upgrade#

The need to upgrade their studs since broken steering studs can

83 toyota pickup bump stops install driver#

This isД®ntirely possible if the driver is gentle and the steering arm stud

Stud while running their 38вЂќ Swampers for the last 10 years. Some wheelers will tell you that theyвЂ™ve never broken a steering arm YouвЂ™ll get a tremendous amount of peace of mind and can start worryingДЄbout the next weak part on your axle. Minimum of one of the вЂњProven Knuckle Stud UpgradesвЂќ below and do it. WeвЂ™ll say this: If you wheel a lot, you should pick a You should upgrade your ToyotaвЂ™s knuckle studs (Like, settle downДЄlready guysвЂ¦). There are lots of heated discussions on the Internet about whether Proper installation and torque so important so make sure you read our tips! вЂњOh,вЂќ you say, вЂњI only haveДЈ1s.вЂќ It doesnвЂ™t matter. Your steering is not designed for this, so what happens? Your

Instead of your studs creating a clamping force from the steering arm to the knuckle, now they have to deal with a large shearingДЇorce. That if you ran the Rubicon 10 times in a row in your Mini on 37s, youвЂ™d WeвЂ™re not sure how this works exactly, but we do know The problem is that fourwheeling will loosen up the Steering studs donвЂ™t shear just because theyвЂ™re weak - itвЂ™s also you,ДЇine reader!!! You gotta do maintenance on your studs before big